⎝⎛sag沙龙国际⎞⎠

Hotline: 021-60839008

Dimming control module

Your location : ⎝⎛sag沙龙国际⎞⎠ > Products & Application Cases

4-way 10A high power leading edge dimming box

Release time: 2018-07-16 15:15




1 产品简介 2- 1 Product Introduction

0/1-10V信号,可对白炽灯、 220V 的卤素灯、以及装设可调光电子变压器的低压卤素灯调光,功率调光器单回路的输出功率可以达到 2 KW。 Leading-edge power dimmers can adjust incandescent lamps, 220V halogen lamps, and low-voltage halogen lamps with dimmable electronic transformers by inputting 0 / 1-10V signals. The output power of a single circuit of the power dimmer can reach 2 KW.

: DK2000-CDV 0 41 0L Model : DK2000-CDV 0 41 0L

: Power :            2 0V 50HZ 2 2 0V 50HZ

: Control signal input :   0 / 1-10V

: Output power :    * 4路 2KW * 4 channels


2 2- 2   Features

  • ≥200us Stable dimming output, rise time ≥200us

  • Multiple temperature protection, safe and reliable

  • Shaft wiring cover design, convenient wiring                            

  • 75±5°C时,减低输出亮度一半 When the temperature reaches 75 ± 5 ° C, reduce the output brightness by half

  • 4点安装,施工方便 4 point mounting for easy installation

  • 85±5°C时,关闭调光器的输出 Turn off the output of the dimmer when the temperature reaches 85 ± 5 ° C

  • There are wire entry holes on the top, bottom, and back to adapt to various wire entry methods

  • Single power supply, independent circuit breaker protection for output circuit            

  • Equipped with manual automatic transfer switch, manual switch and dimming

  • With short circuit protection function, overload protection function

     

3 2- 3   Technical Parameters

model          0 41 0L DK2000-CDV 0 41 0L            Dimming rise time   220us in 220V

Supply voltage       220V      50HZ 外型尺寸 , 50HZ size            *280*130 mm 235 * 280 * 130 mm

signal input      0 / 1-10V                weight                 . 2 KG 4. 2 KG

60W 60W minimum load                      Installation method           Mount  

AC 0-220V 前沿切相调光 Output load AC 0-220V leading edge phase-cut dimming   , 颜色 铁, 黑色 Housing material , color iron, black

Output Power     W* 4 2K W * 4                    IP 20, EN 60 529 Protection IP 20, EN 60 529

Output current      0A* 4 1 0A * 4                   CE CE

: Terminal wire diameter :      2.5- 4.0mm2              0 --- +45°C Operating temperature range 0 --- + 45 ° C

Load type                               




4 2- 4   mm) Installation size ( mm)




5 2- 5   Terminals


0 41 0L 控制器硬件说明 DK2000-CDV 0 41 0L Controller Hardware Description

project

name

function

Note

1

指示灯 Power indicator

Lights up during normal operation

2

Manual switch

Manually start loop output and shut down

3

Ground terminal

Ground

4

控制信号 0 / 1-10V control signal

Input 0 / 1-10V signal

 

5 ~ 8

4 组调光输出 1- 4 groups of dimming output

4 220V dimming output circuits

 

9

N

Neutral input

 

10

L

Firewire input




6 2- 6   Wiring diagram

7 2- 7   Installation and commissioning

 

  • Wiring specifications

  • 2.5-4mm 2 铜导线 Power phase line: red 2.5-4mm 2 copper wire

    2.5-4mm 2 铜导线 Neutral wire: light blue 2.5-4mm 2 copper wire

    2.5mm 2 铜导线 Ground wire: yellow and green two-color 2.5mm 2 copper wire

  • 4mm 2 以上 铜导线 Load connection: 4mm 2 copper wire

  • 1.0~1.5 mm 2 屏蔽双绞线 0 / 1-10V: 1.0 ~ 1.5 mm 2 shielded twisted pair

  • Open the product package, take out the paper pattern in the package, punch holes in the load-bearing wall, install expansion screws, and then fix the power dimmer on the wall.

  • 0/1-10V端子。 According to the wiring diagram, connect each input, output terminal, 0 / 1-10V terminal.

  • The input power is single-phase power supply, and each separate circuit is connected to the MCB output.

  • 应急情况下,通过长时间按压面板上四个按键可实现手动开关灯光或者调光。 In use, in an emergency, you can manually switch on or off the light by pressing the four keys on the panel for a long time. Long press to enter the manual state, cycle dimming, release the button, the light brightness will stop at the current value. 0/1-10V信号。 Manual state, not receiving 0 / 1-10V signal.

  • 0/1-10V信号的自动状态。 Short press or power off and then on, you can exit the manual state and enter the automatic state of receiving 0 / 1-10V signal.

  • Turn off the air switch to completely cut off the load power.


<< back to list

Eastern Region
点击这里给我发消息
Northern Region
点击这里给我发消息
Southern Region
点击这里给我发消息
West China
点击这里给我发消息
Central China
点击这里给我发消息

shut down
真人游戏平台注册 七乐彩 必赢真人娱乐 欢乐拼三张