⎝⎛sag沙龙国际⎞⎠

Hotline: 021-60839008

Dimming control module

Your location : ⎝⎛sag沙龙国际⎞⎠ > Products & Application Cases

12 way 10A high power leading edge dimming box

Release time: 2018-07-16 16:40




1 产品简介 2- 1 Product Introduction

0/1-10V信号,可对白炽灯、 220V 的卤素灯、以及装设可调光电子变压器的低压卤素灯调光,功率调光器单回路的输出功率可以达到 2 KW。 Leading-edge power dimmers can adjust incandescent lamps, 220V halogen lamps, and low-voltage halogen lamps with dimmable electronic transformers by inputting 0 / 1-10V signals. The output power of a single circuit of the power dimmer can reach 2 KW.

: DK2000-CDV121 0L Model : DK2000-CDV121 0L

: 交流380V Power : AC 380V

: 0/1-10V Control signal input : 0 / 1-10V

: 2 2 0V 50HZ Output : 2 2 0V 50HZ

: 2KW * 12路 Output power : 2KW * 12

2 2- 2   Features

  • 0 / 1-10V low voltage control, more secure

  • Multiple temperature protection, safe and reliable

  • ≥200us Stable dimming output, rise time ≥200us

  • Hanging installation, convenient construction   

  • 75±5°C时,减低输出亮度一半 When the temperature reaches 75 ± 5 ° C, reduce the output brightness by half

  • 85±5°C时,关闭调光器的输出 Turn off the output of the dimmer when the temperature reaches 85 ± 5 ° C

  • There are wire entry holes on the top, bottom, and back to adapt to various wire entry methods

  • Three-phase or single power supply can be used            

  • Equipped with manual automatic transfer switch, manual switch and dimming

     

3 2- 3   Technical Parameters

model          0L DK2000-CDV121 0L            220us in 220V Dimming rise time 220us in 220V

Supply voltage       V 380 V      50HZ 外型尺寸 , 50HZ size              * 320 *130 mm 630 * 320 * 130 mm

signal input      0 / 1-10V             weight                 KG 17.8 KG

60W 60W minimum load                          Installation method            Mount  

Output load      0-220V                      , 颜色 铁, 黑色 Housing material , color iron, black

Output Power     W* 12 2K W * 12                        IP 20, EN 60 529 Protection IP 20, EN 60 529

Output current      0A* 12 1 0A * 12                       CE UL CE UL

: 2.5- 4.0mm2 Terminal wire diameter : 2.5- 4.0mm2                   0 --- +45°C Operating temperature range 0 --- + 45 ° C

Load type                               






mm) 2-4 installation dimensions ( mm)







5 2- 5   Terminals


0L 控制器硬件说明 DK2000-CDV121 0L Controller Hardware Description

project

name

function

Note

1

L1

火线输入 AC380V FireWire Input

2

L2

火线输入 AC380V FireWire Input

3

L3

火线输入 AC380V FireWire Input

4

N

Neutral input

 

5 ~ 16

12 组调光输出 1- 12 groups of dimming output

12-channel 220V dimming output circuit

 

17

Signal input 0 / 1-10V

Input 0 / 1-10V signal

 

18

Ground wire

Ground

19

Indicator light

Lights up during normal operation

 

20

Manual dimming

调光 输出 Manual dimming output

 

 

 

6 2- 6   Wiring diagram


7 2- 7   Installation and commissioning

  • Wiring specifications

  • 2.5-4mm 2 铜导线 Power phase line: red 2.5-4mm 2 copper wire

    2.5-4mm 2 铜导线 Neutral wire: light blue 2.5-4mm 2 copper wire

    2.5mm 2 铜导线 Ground wire: yellow and green two-color 2.5mm 2 copper wire

  • 4mm 2 以上 铜导线 Load connection: 4mm 2 copper wire

  • 1.0~1.5 mm 2 屏蔽双绞线 0 / 1-10V: 1.0 ~ 1.5 mm 2 shielded twisted pair

  • Open the product package, take out the paper pattern in the package, punch holes in the load-bearing wall, install expansion screws, and then fix the power dimmer on the wall

  • 0/1-10V端子 Connect each input and output terminal according to the wiring diagram, 0 / 1-10V terminal

  • 满足三相功率平衡时,输入端电源也可以采用单相供电,单项电源进线同时连接到三个输入端子上(输入端子并联) When satisfying the three-phase power balance, the input power can also adopt single-phase power supply, and a single power supply line is connected to three input terminals simultaneously (input terminals are connected in parallel)

  • 19)闪烁,通过按压面板上(20)对应的1--12个按键分别输出1-12路调光,按键按住不放时为调光,点按时为退出手动状态,接收前级0/1-10V信号。 When the power is on, the indicator light ( 19) flashes. By pressing the corresponding 1--12 buttons on the panel (20), 1-12 channels of dimming will be output respectively. Receive the previous stage 0 / 1-10V signal. The manual status is the priority. Without exiting the manual status, the 0 / 1-10V signal cannot control the device. When the 0 / 1-10V signal is input to the first group of signal input terminals (A) of the signal input terminal (17), the first circuit of the corresponding output terminal (5) will output an AC voltage corresponding to it. A --- L is 0 / 1-10V signal terminals corresponding to 5-16 AC output terminals respectively.

For details, please consult our technical staff !

<< back to list

Eastern Region
点击这里给我发消息
Northern Region
点击这里给我发消息
Southern Region
点击这里给我发消息
West China
点击这里给我发消息
Central China
点击这里给我发消息

shut down
真人游戏平台注册 七乐彩 必赢真人娱乐 欢乐拼三张